3D Grafting with a Hook

All of the free patterns and tutorials on this website are supported by my amazing Patreons! If it wasn't for them I wouldn't be able to continue to produce or host freebies. We'd love to have you join us, and in return, you get exclusive behind-the-scenes material, members-only discounts and early access to new free content. Membership starts at $1 per month. You can also say thanks for the freebie via the Tip Jar.

Knitters do use hooks, y'know. For the odd thing, like picking up dropped stitches and adding a nice little picot edge or something. Personally though, I reckon they're under used. For starters, I much prefer to use a hook to do the bind-off I explained in my Tri-Peak pattern... easier than a 3-needle bind-off, yet giving the same results – invisible on one side, nice detailed finish on the other.

Also consider this... you're working something top down... you want to keep going 'till you run out of yarn... but how do you calculate how much yarn you need to save to be able to cast off? Well, don't stress about it. Keep knitting 'till you have your regular 3 or 4 inches (7.4 to 10 centimetres) left or to the end of the round or row, and just pick up your hook. Slip the first 2 stitches onto the hook, pass over the first one, slip the next stitch off the needle, pass over again, and keep going to the last remaining stitch, finish as usual. Gives the same finish without the worry. Think about how you cast off...

Now, I've been practicing picking up stitches and grafting extras onto my Hats. There probably is a traditional, tried and tested way of doing this, but then I'm not one for convention. And I like to find things out for myself ;) I've found the way that gives the neatest results is to use a crochet hook. And that's whats gonna be explained here.

1) Basically, I use the hook to slip underneath the stitches to get a more even 'pick-up'. The hook allows you to slide in under the 'V' (presuming you're working in stocking stitch) and pull your new yarn through with ease. Obvious really, eh?

2) The real trick though, is get an even line across your stitches, so that there's no wonky edge to your grafting. It's best to follow the line of V's that make up your row for grafting in straight lines. For hats and adding to the crown, it's recommended to graft onto a decrease row, as these naturally follow a circular-ish shape (again presuming that you want to graft an even circular shape in the centre of the crown).

3) Oh, and do remember that you need to pick up both sides of the 'V'… the first photo here shows the hook slid underneath the first stitch... the bottom of the 'V' is linked into the previous row, showing the 2 sides of the stitch that need to be picked up. Make sense? Doh... if my words aren't clear, then please follow the photos!

4) For good results, use a yarn that's close in gauge to the one you used for the main body of the item. This Hat was knitted in Rowan Big Wool, and the graft is knitted in remnants of hand-dyed chunky. A slightly different gauge, true, but probably as different as this technique will allow for. For even neater results, use a size smaller hook than recommended – I think I used either a 5mm or 5.5mm (US 8 or 9) for this graft, yet this yarn knits comfortably on 6mm (US 10). Mind, I always use a size smaller for my Hats... helps keep the wind out ;) Once you've picked up sufficient stitches, slip them evenly onto your DPNs and away you go.

5) I picked up a total of 17 stitches for this graft (aiming for 4 stitches on each needle) with the extra stitch at the start of the round – which I then (knit 2 together to make sure there were no unsightly holes. If in doubt, pick up more stitches than you need and decrease them on the first round. This one may look square-ish, but that's just the needles holding it all like that. If you look at the finished graft, and at the last photo which shows it from the inside, you'll see it's circular.

6) To shape your graft, use decreases and increases as you see fit; just remember that anything too large will add weight.. but then that may be the effect you want! I added a small amount of toy stuffing to this one, just before I decreased sufficiently to start the I-cord.

It's not that difficult is it?! You could also stay with the hook and crochet your graft, which I did for another Hat – works just as well, and in fact suits free-forming better, giving more unusual shapes. You don't have to stick with working the crown on Hats either… once you've got the hang of picking up the stitches evenly, there's lots you could do... my notebook is full of ideas based on this method ;)

Right then, if I've missed something out, something isn't clear or you need more help, just leave a comment here and I'll see what I can do. And as usual, I ask to see photos of what you've been up to... now go knit and experiment – it's good for you!

Post edit:

Firstly, when inserting the hook, make sure it goes towards the base of the V, and not across an inverted V – that is, across two stitches.

Secondly, I looked up this method. I only bought my copy of Montse Stanley's 'Knitters Handbook' 6 months ago, second hand, and don't look at it often enough. Checked out grafting but all they had were various takes on Kitchener stitch. It had to be in there… there's no way I'd discovered a new technique. I eventually found it on page 191, under 'picking up stitches'. All that's discussed is picking up stitches in horizontal or vertical straight lines to form rectangles, primarily for pockets. This seems a bit... limited... like, who said pockets had to be flat and rectangular, anyway? To graft means to 'fix or join permanently', and in my mind this means more than seams or pockets. So I've changed the title of this post to reflect that, and avoid confusion.

Support

As always, if you have a question about this technique or need some help with it, leave a comment below! I’m afraid I’m unable to offer help via email or private message but you’re welcome to post in our forums.